尊龙凯时人生就是博

Contact Us：
+86-028-85255257
sales@f-tone.com

高速线缆

标准协议光�？�

兼容协议光�？�

其它种类光器件

手艺支持

光�？橹�

QSFP+转4*10G SFP+分支型无源电缆

0.0/5 rating (0 votes)

Description

F-tone公司提供QSFP+ 转 4*10G SFP+ 分支型无源电缆、40G QSFP+ to 4×10G SFP+ Breakout Passive Copper Cable，应用于客户侧40G以太网和10G以太网LAN中，该产品普遍应用于焦点路由器和数据中心场景中。100%完善兼容全系列品牌交流机,路由器,PDH/SDH传输装备,EPON,GPON,10G EPON,10G GPON,WDM PON基站等等全系列装备

QSFP-4SFP-Cables

Hybrid Passive Copper QSFP+ to 4x SFP+

40G QSFP+ to 4x 10G SFP+ Direct Attach Passive Copper Cables

Features

Hybrid cable conforms to the Small Form Factor SFF-8436 and SFF-8431
Support for multi-gigabit data rates :1.0 Gbps - 10.3125 Gbps (per channel)
Maximum aggregate data rate: 41.25 Gbps (4 x 10.3125Gbit/s)
Hybrid cable link length up to 5m (passive limiting)
High-Density QSFP 38-PIN and 4x SFP 20-PIN Connector
Power Supply :+3.3V
Low power consumption: 0.02 W (typ.)
Temperature Range: 0~ 70 °C

Applications

40G QSFP+ to 4×10SFP+

10G/40Gigabit Ethernet
InfiniBand SDR, DDR, QDR
Switches, Routers, and HBAs
Data Centers
Fibre Channel

STANDARDS COMPLIANCE

QSFP+

SFF-8436
QDR InfiniBand
QSFP+ MSA
RoHS Compliant

SFP+

SFF-8431
SFP+ MSA
RoHS Compatible

Product Description

The QSFP+ to 4x SFP+ Passive cable assemblies are high performance，cost effective for SFP+ and QSFP+ equipment interconnects . The Hybrid cables are compliant with SFF-8436 and SFF-8431 specifications. It is offer a low power consumption，short reach interconnect applications. The cable each lane is capable of transmitting data at rates up to 10Gb/s ,providing an aggregated rate of 40Gb/s.

Recommended Operating Conditions

Parameter	Symbol	Min	Typical	Max	Unit
Storage Ambient Temperature		-40		+85	°C
Operating Case Temperature	Tc	0		+70	°C
Power Supply Voltage	V_CC3	3.14	3.3	3.47	V
Power Dissipation	PD			0.02	W

QSFP+ Pin Descriptions

Pin	Logic	Symbol	Name/Description	Notes
1		GND	Ground	1
2	CML-I	Tx2n	Transmitter Inverted Data Input
3	CML-I	Tx2p	Transmitter Non-Inverted Data Input
4		GND	Ground	1
5	CML-I	Tx4n	Transmitter Inverted Data Input
6	CML-I	Tx4p	Transmitter Non-Inverted Data Input
7		GND	Ground	1
8	LVTTL-I	ModSelL	Module Select
9	LVTTL-I	ResetL	Module Reset
10		Vcc Rx	+3.3V Power Supply Receiver	2
11	LVCMOSI/O	SCL	2-wire serial interface clock
12	LVCMOSI/O	SDA	2-wire serial interface data
13		GND	Ground	1
14	CML-O	Rx3p	Receiver Non-Inverted Data Output
15	CML-O	Rx3n	Receiver Inverted Data Output
16		GND	Ground	1
17	CML-O	Rx1p	Receiver Non-Inverted Data Output
18	CML-O	Rx1n	Receiver Inverted Data Output
19		GND	Ground	1
20		GND	Ground	1
21	CML-O	Rx2n	Receiver Inverted Data Output
22	CML-O	Rx2p	Receiver Non-Inverted Data Output
23		GND	Ground	1
24	CML-O	Rx4n	Receiver Inverted Data Output
25	CML-O	Rx4p	Receiver Non-Inverted Data Output
26		GND	Ground	1
27	LVTTL-O	ModPrsL	Module Present
28	LVTTL-O	IntL	Interrupt
29		Vcc Tx	+3.3V Power supply transmitter	2
30		Vcc1	+3.3V Power supply	2
31	LVTTL-I	LPMode	Low Power Mode
32		GND	Ground	1
33	CML-I	Tx3p	Transmitter Non-Inverted Data Input
34	CML-I	Tx3n	Transmitter Inverted Data Input
35		GND	Ground	1
36	CML-I	Tx1p	Transmitter Non-Inverted Data Input
37	CML-I	Tx1n	Transmitter Inverted Data Input
38		GND	Ground	1

Note 1: GND is the symbol for signal and supply (power) common for the QSFP+ module. All are common within the QSFP+ module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal-common ground plane.

Note 2: Vcc Rx, Vcc1 and Vcc Tx are the receiver and transmitter power supplies and shall be applied concurrent- ly. Requirements defined for the host side of the Host Edge Card Connector are listed in Table 6. Recommended host board power supply filtering is shown in Figure 4. Vcc Rx Vcc1 and Vcc Tx may be internally connected with- in the QSFP+ Module module in any combination. The connector pins are each rated for a maximum current of 500 mA.

SFP+ Pin Descriptions

Pin	Logic	Symbol	Name/Description	Notes
1		VeeT	Transmitter Ground
2	LV-TTL-O	TX_Fault	N/A	1
3	LV-TTL-I	TX_DIS	Transmitter Disable	2
4	LV-TTL-I/O	SDA	Tow Wire Serial Data
5	LV-TTL-I	SCL	Tow Wire Serial Clock
6		MOD_DEF0	Module present, connect to VeeT
7	LV-TTL-I	RS0	N/A	1
8	LV-TTL-O	LOS	LOS of Signal	2
9	LV-TTL-I	RS1	N/A	1
10		VeeR	Reciever Ground
11		VeeR	Reciever Ground
12	CML-O	RD-	Reciever Data Inverted
13	CML-O	RD+	Reciever Data Non-Inverted
14		VeeR	Reciever Ground
15		VccR	Reciever Supply 3.3V
16		VccT	Transmitter Supply 3.3V
17		VeeT	Transmitter Ground
18	CML-I	TD+	Transmitter Data Non-Inverted
19	CML_I	TD-	Transmitter Data Inverted
20		VeeT	Transmitter Ground

1. Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor

2. Passive cable assemblies do not support LOS and TX_DIS

Ordering information

Part Number	Product Description
QSFP-4SFPPC-01	QSFP+ To 4X SFP+ Direct Attach Cables, 1m (30AWG),0?C ~ +70?C
QSFP-4SFPPC-03	QSFP+ To 4X SFP+ Direct Attach Cables, 3m (30AWG),0?C ~ +70?C
QSFP-4SFPPC-04	QSFP+ To 4X SFP+ Direct Attach Cables, 5m (28AWG),0?C ~ +70?C

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone before they become applicable to any particular order or contract. In accordance with the F-tone policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone or others. Further details are available from any F-tone sales representative.

sitemap、网站地图